Announcement

Collapse
No announcement yet.

NERO - Could not perform end of Disc-at-once

Collapse
X
 
  • Time
  • Show
Clear All
new posts
  • MINIMOKE
    Junior Member
    Junior Member
    • Sep 2004
    • 10

    NERO - Could not perform end of Disc-at-once

    Hi,

    I have been having ongoing problems with Nero 6 for a while now.

    Original problem was that some movies, ripped by DVDDecrypter, shrunk by DVDShrink and then burnt using Nero failed at the Nero stage. Even the ones that worked seemed to take ages to burn.

    I updated Nero to 3.2.1.20 and also updated the firmware of my DVD drive.

    I'm not sure whether these steps have made things worse, but now Nero fails to burn all the time (even using it on its own) with the following errors:
    "Write error"
    "Could not perform end of Disc-at-once"

    I have tried different media (FujiFilm and Maxell as well as cheap no-name) and I still get errors. The drive works fine as a player and the firmware upgrade seemed to go smoothly.

    Yesterday I removed the CD and DVD drive from the PC, uninstalled Nero, DVDShrink and DVD Decrypter and cleaned the registry with a Nero utility and also RegCleaner.

    I then reinstalled the drives and only Nero (3.2.1.20). I still get errors and I'm still unable to burn a DVD. I have tried various types of data (large MPG using UDF and normal PC files using ISO).

    I have attached is the complete Nero Logfile as a PDF, some of it is below:

    Windows 2000 5.0
    IA32
    WinAspi: -
    ahead WinASPI: File 'C:\Program Files\Ahead\nero\Wnaspi32.dll': Ver=2.0.1.68, size=160016 bytes, created 22/07/2004 5:33:44 PM
    Nero version: 6.3.1.20
    Recorder: <HL-DT-ST DVDRAM GSA-4081B>Version: A104 - HA 1 TA 0 - 6.3.1.20
    Adapter driver: <atapi> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ATAPI
    CD-ROM: <ASUS CRW-4816A >Version: 1.0 - HA 1 TA 1 - 6.3.1.20
    Adapter driver: <atapi> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD400JB-00ENA0 atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : HL-DT-ST DVDRAM GSA-4081B atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : ASUS CRW-4816A atapi Port 1 ID 1 DMA: On

    === CDRom-Device-Map ===
    HL-DT-ST DVDRAM GSA-4081 H: CDRom3
    ASUS CRW-4816A G: CDRom2
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 38797312 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 239MB (245280kB)
    Free physical memory: 94MB (96876kB)
    Memory in use : 60 %
    Uncached PFiles: 0x0
    Use Static Write Speed Table: 0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    31.8.2004
    ISO compilation
    9:42:25 PM #1 Text 0 File Isodoc.cpp, Line 6065
    Iso document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : TRUE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet : TRUE
    Allow pathdepth more than 8 directories : TRUE
    Allow more than 255 characters in path : TRUE
    Write ISO9660 ;1 file extensions : TRUE


    9:42:26 PM #11 Text 0 File ThreadedTransferInterface.cpp, Line 984
    Prepare recorder [HL-DT-ST DVDRAM GSA-4081B] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 913080320, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_RecDep_|_CtrlAdr_
    0 | lead-in | 0 | 0x00 | 0x41
    0 | 1 | 0 | 0x00 | 0x41
    0 | 1 | 1 | 0x00 | 0x41
    445840 | lead-out | 1 | 0x00 | 0x41

    9:42:26 PM #12 Phase 24 File dlgbrnst.cpp, Line 1855
    Caching of files started

    9:42:29 PM #13 Text 0 File Burncd.cpp, Line 4183
    Cache writing successful.

    9:42:29 PM #14 Phase 25 File dlgbrnst.cpp, Line 1855
    Caching of files completed

    9:42:29 PM #15 Phase 32 File dlgbrnst.cpp, Line 1855
    Simulation started at 4x (5,540 KB/s)

    9:42:29 PM #16 Text 0 File ThreadedTransferInterface.cpp, Line 2344
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    9:42:29 PM #17 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 3:17,335 (197335ms) -> OK

    9:42:29 PM #18 Text 0 File DVDR.cpp, Line 1942
    Recording mode: Sequential Recording Mode

    9:42:29 PM #19 Text 0 File Mmc.cpp, Line 20531
    Set BUFE: supported -> ON

    9:42:29 PM #20 Text 0 File DVDR.cpp, Line 2083
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    9:42:29 PM #21 Text 0 File Cdrdrv.cpp, Line 8128
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 5
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 26127F h
    End Sector Number in Layer 0: 0 h
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 2FE10 h
    Start sector number of the next Border-In: 2FFA0 h
    Media Specific [16..63]:
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 02 FE 10 00 02 FF A0 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    9:42:32 PM #22 Text 0 File Cdrdrv.cpp, Line 1294
    21:42:32.539 - HL-DT-ST DVDRAM GSA-4081B\H1 T0 : Queue again later

    9:45:39 PM #23 Text 0 File WriterStatus.cpp, Line 115
    <HL-DT-ST DVDRAM GSA-4081B> start writing Lead-Out at LBA 445840 (6CD90h), lenght 0 blocks

    9:45:40 PM #24 Text 0 File ThreadedTransfer.cpp, Line 229
    all writers idle, stopping conversion

    9:45:40 PM #25 Text 0 File DVDR.cpp, Line 2325
    EndDAO: Last written address was 445839

    9:46:13 PM #26 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK

    9:46:13 PM #27 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK

    9:46:13 PM #28 Phase 33 File dlgbrnst.cpp, Line 1855
    Simulation completed successfully at 4x (5,540 KB/s)

    9:46:14 PM #29 Phase 36 File dlgbrnst.cpp, Line 1855
    Burn process started at 4x (5,540 KB/s)

    9:46:14 PM #30 Text 0 File ThreadedTransferInterface.cpp, Line 2344
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    9:46:14 PM #31 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 3:17,335 (197335ms) -> OK

    9:46:14 PM #32 Text 0 File DVDR.cpp, Line 1942
    Recording mode: Sequential Recording Mode

    9:46:14 PM #33 Text 0 File Mmc.cpp, Line 20531
    Set BUFE: supported -> ON

    9:46:14 PM #34 Text 0 File DVDR.cpp, Line 2083
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    9:46:14 PM #35 Text 0 File Cdrdrv.cpp, Line 8128
    ---- DVD Structure: Physical Format Information (00h) ----
    Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
    Book Type: DVD-R (2), Part Version: 5
    Disc Size: 120 mm, Maximum Rate: <not specified> (F h)
    Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
    Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
    Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
    End Physical Sector Number of Data Area: 9CD8F h
    End Sector Number in Layer 0: 0 h
    Data in Burst Cutting Area (BCA) does not exist
    Start sector number of the current Border-Out: 0 h
    Start sector number of the next Border-In: 0 h
    Media Specific [16..63]:
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
    00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

    9:46:25 PM #36 SCSI -1135 File Cdrdrv.cpp, Line 1442
    SCSI Exec, HA 1, TA 0, LUN 0, buffer 0x06800000
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x03 (KEY_MEDIUM_ERROR)
    Sense Code: 0x0C
    Sense Qual: 0x00
    CDB Data: 0x2A 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x20 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x10
    0x32 0x4D 0x03 0x0C 0x0C 0x00

    9:46:25 PM #37 CDR -1135 File Writer.cpp, Line 304
    Write error

    9:46:25 PM #38 Text 0 File ThreadedTransfer.cpp, Line 229
    all writers idle, stopping conversion

    9:46:25 PM #39 Text 0 File ThreadedTransfer.cpp, Line 223
    conversion idle, stopping reader

    9:46:25 PM #40 Text 0 File DVDR.cpp, Line 2325
    EndDAO: Last written address was -1

    9:46:25 PM #41 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK

    9:46:25 PM #42 CDR -1135 File WriterStatus.cpp, Line 164
    Write error

    9:46:25 PM #43 TRANSFER -24 File WriterStatus.cpp, Line 164
    Could not perform end of Disc-at-once

    9:46:25 PM #44 Text 0 File dlgbrnst.cpp, Line 1713
    Set remaining time: 0:00,000 (0ms) -> OK

    9:46:25 PM #45 Phase 38 File dlgbrnst.cpp, Line 1855
    Burn process failed at 4x (5,540 KB/s)


    Existing drivers:
    File 'Drivers\atapi.sys': Ver=5.00.2195.6699, size=86672 bytes, created 19/06/2003 12:05:04 PM (Adapter driver for rec)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)


    I hope someone can help.

    Dave.
    Attached Files
Working...
😀
🥰
🤢
😎
😡
👍
👎