Showing results 1 to 6 of 6

Thread: Help with Nero 6

  1. #1
    Platinum Member
    Platinum Member

    Join Date
    Jul 2005
    Posts
    198

    Default Help with Nero 6

    Hi all

    I have been using Nero 6 for quite a while. When i was using fuji DVD+Rs I would occasionally get an error with a bad burn (even though the disc was fully burned and played fine??) usually with the message failed to close DAO.

    Well anyhow I switched DVD+Rs to Verbatim. I have burned many DVDs since with no errors, suddenly the last few days I've had 3 bad burns with the following error log, if anyone can help I would appreciated this.
    What makes it extra annoying is that the errors only happens at the end of the burn, so i get to wait a full 15 min to find out if the DVD is any good. ERRR......

    Now keep in mind I've used the below settings for all of the successful burns I have made and only recently with the verbatims ahve i been recieving bad burns; however I recieved them (the errors) more often in the past when using FUJI DVD+Rs (not all the time but I was never 100% cofident when I burned a DVD that it would come out OK)

    STATS: Win XP SP2, 512 MB RAM 400MHz, P4 HT 2.6GHz.
    NEC 1100 DVD+R flashed (herrie mod firmware) to a NEC 1300 +/-DVD 4x max burn speed

    LOG:
    fffff
    ffff
    Nero Serial Removed
    Windows XP 5.1
    IA32
    WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 7:06:00 AM
    ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
    Nero Version: 6.6.0.16
    Internal Version: 6, 6, 0, 16b
    (Nero Express)
    Recorder: <_NEC DVD_RW ND-1300A> Version: 1.0C - HA 1 TA 1 - 6.6.0.16
    Adapter driver: <atapi> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ATAPI
    CD-ROM: <HL-DT-ST DVD-ROM GDR8162B>Version: 0015 - HA 1 TA 0 - 6.6.0.16
    Adapter driver: <atapi> HA 1
    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD800BB-75CAA0 atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : HL-DT-ST DVD-ROM GDR8162B atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : _NEC DVD_RW ND-1300A atapi Port 1 ID 1 DMA: On
    === CDRom-Device-Map ===
    HL-DT-ST DVD-ROM GDR8162B D: CDRom0
    _NEC DVD_RW ND-1300A E: CDRom1
    =======================
    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 74448896 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 510MB (523244kB)
    Free physical memory: 157MB (161648kB)
    Memory in use : 69 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)
    5.12.2005
    UDF/ISO compilation
    10:56:55 AM #1 Phase 112 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation started

    10:56:56 AM #2 Phase 114 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation completed (no file modified)

    10:56:56 AM #3 Text 0 File Isodoc.cpp, Line 6356
    UDF document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    UDF Mode : UDF/ISO bridge
    UDF Revision : 1.02
    UDF Partition Type : physical
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet :FALSE
    Allow pathdepth more than 8 directories : FALSE
    Allow more than 255 characters in path : FALSE
    Write ISO9660 ;1 file extensions : TRUE

    10:56:56 AM #4 Phase 111 File dlgbrnst.cpp, Line 1832
    DVD-Video files sorted

    10:56:56 AM #5 Text 0 File Reader.cpp, Line 127
    Reader running

    10:56:56 AM #6 Text 0 File Writer.cpp, Line 122
    Writer _NEC DVD_RW ND-1300A running

    10:56:56 AM #7 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    10:56:56 AM #8 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    10:56:56 AM #9 Text 0 File Burncd.cpp, Line 3233
    Turn on Disc-At-Once, using DVD media

    10:56:56 AM #10 Text 0 File DlgWaitCD.cpp, Line 270
    Last possible write address on media: 2295103 (510:01.28, 4482MB)
    Last address to be written: 2286111 (508:01.36, 4465MB)

    10:56:56 AM #11 Text 0 File DlgWaitCD.cpp, Line 282
    Write in overburning mode: NO (enabled: CD)

    10:56:56 AM #12 Text 0 File DlgWaitCD.cpp, Line 2483
    Recorder: _NEC DVD_RW ND-1300A, Media type: DVD+R

    10:56:56 AM #13 Text 0 File DlgWaitCD.cpp, Line 448
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    10:56:56 AM #14 Text 0 File ThreadedTransferInterface.cpp, Line 838
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [_NEC DVD_RW ND-1300A]
    --------------------------------------------------------------

    10:56:56 AM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1051
    Prepare recorder [_NEC DVD_RW ND-1300A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    2286112 | lead-out | 1 | 0x41 | 0x00

    10:56:56 AM #16 Phase 24 File dlgbrnst.cpp, Line 1832
    Caching of files started

    10:56:56 AM #17 Text 0 File Burncd.cpp, Line 4120
    Cache writing successful.

    10:56:56 AM #18 Phase 25 File dlgbrnst.cpp, Line 1832
    Caching of files completed

    10:56:56 AM #19 Phase 36 File dlgbrnst.cpp, Line 1832
    Burn process started at 4x (5,540 KB/s)

    10:56:56 AM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2654
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    10:56:56 AM #21 SCSI -1066 File Cdrdrv.cpp, Line 1180
    SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x0C280600
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x24
    Sense Qual: 0x00
    CDB Data: 0xAD 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x08 0x04 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x24 0x00

    10:56:56 AM #22 Text 0 File DVDPlusRW.cpp, Line 665
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    11:11:17 AM #23 Text 0 File WriterStatus.cpp, Line 116
    <_NEC DVD_RW ND-1300A > start writing Lead-Out at LBA 2286112 (22E220h), lenght 0 blocks

    11:11:17 AM #24 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    11:11:31 AM #25 SCSI -1106 File Cdrdrv.cpp, Line 1180
    SCSI Exec, HA 1, TA 1, LUN 0
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x03 (KEY_MEDIUM_ERROR)
    Sense Code: 0x73
    Sense Qual: 0x03
    CDB Data: 0x5B 0x01 0x01 0x00 0x00 0x01 0x00 0x00 0x00 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x03 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x73 0x03

    11:11:31 AM #26 SCSI -1176 File Cdrdrv.cpp, Line 1180
    SCSI Exec, HA 1, TA 1, LUN 0
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x72
    Sense Qual: 0x03
    CDB Data: 0x5B 0x01 0x06 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x72 0x03

    11:11:31 AM #27 CDR -1176 File ThreadedTransferInterface.cpp, Line 1909
    Session fixation error

    11:11:31 AM #28 TRANSFER -24 File ThreadedTransferInterface.cpp, Line 1909
    Could not perform end of Disc-at-once

    11:11:51 AM #29 Phase 127 File dlgbrnst.cpp, Line 1832
    Generating DVD high compatibility borders

    11:11:51 AM #30 Phase 129 File dlgbrnst.cpp, Line 1832
    Generating DVD borders completed successfully

    11:11:51 AM #31 Phase 38 File dlgbrnst.cpp, Line 1832
    Burn process failed at 4x (5,540 KB/s)

    Existing drivers:
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
    File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/11/2005 5:28:13 PM (Prassi/Veritas driver for win 2K)
    File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/4/2004 12:59:42 AM (Adapter driver for rec)
    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

  2. #2
    Super Moderator
    Chewy's Avatar
    Join Date
    Nov 2003
    Location
    millenium falcon
    Posts
    18,971

    Default

    congrats on finding that crossflash, it's gone as far as I know now.
    still so old the media codes are out of date
    your's is not identifying the media right, must be firmware(2004-07-29)
    WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 7:06:00 AM
    probably causing problems, shouldn't be there,
    probably hitched a ride with these which should not be there either
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
    File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/11/2005 5:28:13 PM (Prassi/Veritas driver for win 2K)

    sonic or veritas software???

    many problems

  3. #3
    Platinum Member
    Platinum Member

    Join Date
    Jul 2005
    Posts
    198

    Default

    what??

    how do i fix this
    why all of a sudden is this causing problems?

    Also i just re-burned the DVD and it said it was successful, THEN it started verifying the data?? (i didn't have that checked)
    so i stopped it and it said the burn failed (although i think that just refers to the verification)

    what do i do?
    here is the log from the second burn
    fffff
    ffff
    1A23-3157-9030-4102-5778-2095

    Windows XP 5.1
    IA32
    WinAspi: File 'Wnaspi32.dll': Ver=4.60 (1021), size=45056 bytes, created 9/10/1999 7:06:00 AM
    ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 10/26/2004 6:35:34 PM
    Nero Version: 6.6.0.16
    Internal Version: 6, 6, 0, 16b
    (Nero Express)
    Recorder: <_NEC DVD_RW ND-1300A> Version: 1.0C - HA 1 TA 1 - 6.6.0.16
    Adapter driver: <atapi> HA 1
    Drive buffer : 2048kB
    Bus Type : default (0) -> ATAPI, detected: ATAPI
    CD-ROM: <HL-DT-ST DVD-ROM GDR8162B>Version: 0015 - HA 1 TA 0 - 6.6.0.16
    Adapter driver: <atapi> HA 1

    === Scsi-Device-Map ===
    DiskPeripheral : WDC WD800BB-75CAA0 atapi Port 0 ID 0 DMA: On
    CdRomPeripheral : HL-DT-ST DVD-ROM GDR8162B atapi Port 1 ID 0 DMA: On
    CdRomPeripheral : _NEC DVD_RW ND-1300A atapi Port 1 ID 1 DMA: On

    === CDRom-Device-Map ===
    HL-DT-ST DVD-ROM GDR8162B D: CDRom0
    _NEC DVD_RW ND-1300A E: CDRom1
    =======================

    AutoRun : 1
    Excluded drive IDs:
    WriteBufferSize: 74448896 (0) Byte
    ShowDrvBufStat : 0
    BUFE : 0
    Physical memory : 510MB (523244kB)
    Free physical memory: 104MB (107092kB)
    Memory in use : 79 %
    Uncached PFiles: 0x0
    Use Inquiry : 1
    Global Bus Type: default (0)
    Check supported media : Disabled (0)

    5.12.2005
    UDF/ISO compilation
    12:26:55 PM #1 Phase 112 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation started

    12:26:55 PM #2 Phase 114 File dlgbrnst.cpp, Line 1832
    DVD-Video files reallocation completed (no file modified)

    12:26:55 PM #3 Text 0 File Isodoc.cpp, Line 6356
    UDF document burn settings
    ------------------------------------------
    Determine maximum speed : FALSE
    Simulate : FALSE
    Write : TRUE
    Finalize CD : TRUE
    Multisession : FALSE
    Burning mode : DAO
    Mode : 1
    UDF Mode : UDF/ISO bridge
    UDF Revision : 1.02
    UDF Partition Type : physical
    ISO Level : 1 (Max. of 11 = 8 + 3 char)
    Character set : ISO 9660
    Joliet :FALSE
    Allow pathdepth more than 8 directories : FALSE
    Allow more than 255 characters in path : FALSE
    Write ISO9660 ;1 file extensions : TRUE

    12:26:55 PM #4 Phase 111 File dlgbrnst.cpp, Line 1832
    DVD-Video files sorted

    12:26:56 PM #5 Text 0 File Reader.cpp, Line 127
    Reader running

    12:26:56 PM #6 Text 0 File Writer.cpp, Line 122
    Writer _NEC DVD_RW ND-1300A running

    12:26:56 PM #7 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    12:26:56 PM #8 ISO9660GEN -11 File geniso.cpp, Line 3309
    First writeable address = 0 (0x00000000)

    12:26:56 PM #9 Text 0 File Burncd.cpp, Line 3233
    Turn on Disc-At-Once, using DVD media

    12:26:57 PM #10 Text 0 File DlgWaitCD.cpp, Line 270
    Last possible write address on media: 2295103 (510:01.28, 4482MB)
    Last address to be written: 2286111 (508:01.36, 4465MB)

    12:26:57 PM #11 Text 0 File DlgWaitCD.cpp, Line 282
    Write in overburning mode: NO (enabled: CD)

    12:26:57 PM #12 Text 0 File DlgWaitCD.cpp, Line 2483
    Recorder: _NEC DVD_RW ND-1300A, Media type: DVD+R

    12:26:57 PM #13 Text 0 File DlgWaitCD.cpp, Line 448
    >>> Protocol of DlgWaitCD activities: <<<
    =========================================

    12:26:57 PM #14 Text 0 File ThreadedTransferInterface.cpp, Line 838
    Setup items (after recorder preparation)
    0: TRM_DATA_MODE1 ()
    2 indices, index0 (150) not provided
    original disc pos #0 + 2286112 (2286112) = #2286112/508:1.37
    relocatable, disc pos for caching/writing not required/ required, no patch infos
    -> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2286112 blocks [_NEC DVD_RW ND-1300A]
    --------------------------------------------------------------

    12:26:57 PM #15 Text 0 File ThreadedTransferInterface.cpp, Line 1051
    Prepare recorder [_NEC DVD_RW ND-1300A] for write in CUE-sheet-DAO
    DAO infos:
    ==========
    MCN: ""
    TOCType: 0x00; Session Closed, disc fixated
    Tracks 1 to 1:
    1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4681957376, ISRC ""
    DAO layout:
    ===========
    __Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
    0 | lead-in | 0 | 0x41 | 0x00
    0 | 1 | 0 | 0x41 | 0x00
    0 | 1 | 1 | 0x41 | 0x00
    2286112 | lead-out | 1 | 0x41 | 0x00

    12:26:57 PM #16 Phase 24 File dlgbrnst.cpp, Line 1832
    Caching of files started

    12:26:57 PM #17 Text 0 File Burncd.cpp, Line 4120
    Cache writing successful.

    12:26:57 PM #18 Phase 25 File dlgbrnst.cpp, Line 1832
    Caching of files completed

    12:26:57 PM #19 Phase 36 File dlgbrnst.cpp, Line 1832
    Burn process started at 4x (5,540 KB/s)

    12:26:57 PM #20 Text 0 File ThreadedTransferInterface.cpp, Line 2654
    Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

    12:26:57 PM #21 SCSI -1066 File Cdrdrv.cpp, Line 1180
    SCSI Exec, HA 1, TA 1, LUN 0, buffer 0x0C280600
    Status: 0x04 (0x01, SCSI_ERR)
    HA-Status 0x00 (0x00, OK)
    TA-Status 0x02 (0x01, SCSI_TASTATUS_CHKCOND)
    Sense Key: 0x05 (KEY_ILLEGAL_REQUEST)
    Sense Code: 0x24
    Sense Qual: 0x00
    CDB Data: 0xAD 0x00 0x00 0x00 0x00 0x00 0x00 0x00 0x08 0x04 0x00 0x00
    Sense Data: 0x70 0x00 0x05 0x00 0x00 0x00 0x00 0x0A
    0x00 0x00 0x00 0x00 0x24 0x00

    12:26:57 PM #22 Text 0 File DVDPlusRW.cpp, Line 665
    Start write address at LBA 0
    DVD high compatibility mode: Yes

    12:41:02 PM #23 Text 0 File WriterStatus.cpp, Line 116
    <_NEC DVD_RW ND-1300A > start writing Lead-Out at LBA 2286112 (22E220h), lenght 0 blocks

    12:41:02 PM #24 Text 0 File ThreadedTransfer.cpp, Line 228
    all writers idle, stopping conversion

    12:41:20 PM #25 Phase 37 File dlgbrnst.cpp, Line 1832
    Burn process completed successfully at 4x (5,540 KB/s)

    12:41:20 PM #26 Phase 78 File dlgbrnst.cpp, Line 1832
    Data verification started

    12:41:37 PM #27 Phase 40 File dlgbrnst.cpp, Line 1519
    Aborted by user


    Existing drivers:
    File 'Drivers\ADPU160M.SYS': Ver=v3.60a (Lab01_N(johnstra).010529-2218), size=101888 bytes, created 8/17/2001 3:07:32 PM
    File 'Drivers\PXHELP20.SYS': Ver=2.03.28a, size=20640 bytes, created 3/11/2005 5:28:13 PM (Prassi/Veritas driver for win 2K)
    File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 8/4/2004 12:59:42 AM (Adapter driver for rec)

    Registry Keys:
    HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

  4. #4
    Platinum Member
    Platinum Member

    Join Date
    Jul 2005
    Posts
    198

    Default

    now i just burned a dvd with no problems??
    very confused, please help

  5. #5
    Not a god of digital video blutach's Avatar
    Join Date
    Oct 2004
    Location
    is everything!
    Posts
    24,627

    Default

    Sounds like you either have a bad batch of media, or the burner's finally on it's last legs. See how it goes.

    Look at **037200 here.

    Regards

  6. #6
    Platinum Member
    Platinum Member

    Join Date
    Jul 2005
    Posts
    198

    Default

    I went to the link you suggested and looked up my error which is
    Session fixation error writing lead-out
    it claims that either the disc is dirty/ scratch etc or DMA settings
    I checked my DMA settings here is what ihave is this correct?

    Primary Device:
    Device 0: Auto Detection, DMA if avaliable, Ultra DMA Mode 5
    Device 1: Auto Detection, DMA if avaliable, Not Applicable

    Secondary Device:
    Device 0: Auto Detection, DMA if avaliable, Ultra DMA Mode 2
    Device 1: Auto Detection, DMA if avaliable, Ultra DMA Mode 2

    is this ok? if not what and how do i change it? (these are the same settings I have always used though)

Thread Information

Users Browsing this Thread

There are currently 1 users browsing this thread. (0 members and 1 guests)

Bookmarks

Posting Rules

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •