Nero 6.6 Error reading data

**Nick Hope** · 5 Jan 2006, 06:00 PM

To try to rectify the problems I did the following:

Installed the latest drivers for my Asus motherboard's Intel chipset
Upgraded from Nero 6.6.0.16 to 6.6.0.18
Upgraded the DVR-107D from firmware 1.18 to 1.22

Unfortunately I still have "data read errors". Below is my latest log file for a "data read error".

Windows XP 5.1
IA32
WinAspi: -
ahead WinASPI: File 'C:\Program Files\Ahead\Nero\Wnaspi32.dll': Ver=2.0.1.74, size=164112 bytes, created 26/10/2004 18:35:34
Nero Version: 6.6.0.18
Internal Version: 6, 6, 0, 18e

Recorder:
Version: 1.22 - HA 3 TA 0 - 6.6.0.18
Adapter driver: <ATAPI>HA 3
Drive buffer : 2000kB
Bus Type : default (0) -> ATAPI, detected: ATAPI
CD-ROM:
Version: 1.22 - HA 3 TA 0 - 6.6.0.18
Adapter driver: <ATAPI>HA 3

=== Scsi-Device-Map ===
DiskPeripheral : WDC WD2000JB-00DUA0 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD360GD-00FLA0 atapi Port 1 ID 0 DMA: On
DiskPeripheral : WDC WD2500JD-00GBB0 atapi Port 2 ID 0 DMA: On
CdRomPeripheral : PIONEER DVD-RW DVR-107D atapi Port 3 ID 0 DMA: On

=== CDRom-Device-Map ===
PIONEER DVD-RW DVR-107D F: CDRom0
=======================

AutoRun : 1
Excluded drive IDs:
WriteBufferSize: 83886080 (0) Byte
ShowDrvBufStat : 0
BUFE : 0
Physical memory : 1022MB (1047276kB)
Free physical memory: 599MB (614396kB)
Memory in use : 41 %
Uncached PFiles: 0x0
Use Inquiry : 1
Global Bus Type: default (0)
Check supported media : Disabled (0)

4.1.2006
UDF/ISO compilation
11:22:38 #1 Phase 112 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation started

11:22:38 #2 Phase 114 File dlgbrnst.cpp, Line 1832
DVD-Video files reallocation completed (no file modified)

11:22:38 #3 Text 0 File Isodoc.cpp, Line 6359
UDF document burn settings
------------------------------------------
Determine maximum speed : FALSE
Simulate : FALSE
Write : TRUE
Finalize CD : TRUE
Multisession : FALSE
Burning mode : DAO
Mode : 1
UDF Mode : UDF/ISO bridge
UDF Revision : 1.02
UDF Partition Type : physical
ISO Level : 1 (Max. of 11 = 8 + 3 char)
Character set : ISO 9660
Joliet :FALSE
Allow pathdepth more than 8 directories : TRUE
Allow more than 255 characters in path : TRUE
Write ISO9660 ;1 file extensions : TRUE

11:22:38 #4 Phase 111 File dlgbrnst.cpp, Line 1832
DVD-Video files sorted

11:22:38 #5 Text 0 File Reader.cpp, Line 127
Reader running

11:22:38 #6 Text 0 File Writer.cpp, Line 122
Writer PIONEER DVD-RW DVR-107D running

11:22:38 #7 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)

11:22:39 #8 ISO9660GEN -11 File geniso.cpp, Line 3309
First writeable address = 0 (0x00000000)

11:22:39 #9 Text 0 File Burncd.cpp, Line 3233
Turn on Disc-At-Once, using DVD media

11:23:02 #10 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2209087 (490:54.37, 4314MB)

11:23:02 #11 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)

11:23:02 #12 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: PIONEER DVD-RW DVR-107D, Media type: DVD-R
Disc Manufacturer: RITEKG - 04
Disc Application Code: 64, Disc Physical Code: 193

11:23:02 #13 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW.)

11:23:02 #14 Text 0 File ThreadedTransferInterface.cpp, Line 838
Setup items (after recorder preparation)
0: TRM_DATA_MODE1 ()
2 indices, index0 (150) not provided
original disc pos #0 + 2209088 (2209088) = #2209088/490:54.38
relocatable, disc pos for caching/writing not required/ required, no patch infos
-> TRM_DATA_MODE1, 2048, config 0, wanted index0 0 blocks, length 2209088 blocks [PIONEER DVD-RW DVR-107D]
--------------------------------------------------------------

11:23:02 #15 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [PIONEER DVD-RW DVR-107D] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4524212224, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2209088 | lead-out | 1 | 0x41 | 0x00

11:23:02 #16 Phase 24 File dlgbrnst.cpp, Line 1832
Caching of files started

11:23:02 #17 Text 0 File Burncd.cpp, Line 4122
Cache writing successful.

11:23:02 #18 Phase 25 File dlgbrnst.cpp, Line 1832
Caching of files completed

11:23:02 #19 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)

11:23:03 #20 Text 0 File ThreadedTransferInterface.cpp, Line 2661
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

11:23:03 #21 Text 0 File DVDR.cpp, Line 2571
Recording mode: Sequential Recording Mode

11:23:03 #22 Text 0 File Mmc.cpp, Line 21774
Set BUFE: Buffer underrun protection -> ON

11:23:03 #23 Text 0 File DVDR.cpp, Line 2726
Start write address at LBA 0
DVD high compatibility mode: Yes

11:23:03 #24 Text 0 File Cdrdrv.cpp, Line 8892
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <NOT specified>(F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

11:23:05 #25 Text 0 File Cdrdrv.cpp, Line 1288
11:23:05.406 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:23:41 #26 Text 0 File Cdrdrv.cpp, Line 1288
11:23:41.109 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:23:41 #27 Text 0 File Cdrdrv.cpp, Line 1288
11:23:41.156 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:23:41 #28 Text 0 File Cdrdrv.cpp, Line 1288
11:23:41.203 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:28:23 #29 Text 0 File Cdrdrv.cpp, Line 1288
11:28:23.718 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:32:56 #30 Text 0 File Cdrdrv.cpp, Line 1288
11:32:56.734 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:35:22 #31 Text 0 File Cdrdrv.cpp, Line 1288
11:35:22.093 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:37:15 #32 Text 0 File WriterStatus.cpp, Line 116

start writing Lead-Out at LBA 2209088 (21B540h), lenght 0 blocks

11:37:16 #33 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

11:37:16 #34 Text 0 File DVDR.cpp, Line 2969
EndDAO: Last written address was 2209087

11:37:54 #35 Phase 37 File dlgbrnst.cpp, Line 1832
Burn process completed successfully at 4x (5,540 KB/s)

11:38:26 #36 Text 0 File DlgWaitCD.cpp, Line 270
Last possible write address on media: 2298495 (510:46.45, 4489MB)
Last address to be written: 2209087 (490:54.37, 4314MB)

11:38:26 #37 Text 0 File DlgWaitCD.cpp, Line 282
Write in overburning mode: NO (enabled: CD)

11:38:26 #38 Text 0 File DlgWaitCD.cpp, Line 2483
Recorder: PIONEER DVD-RW DVR-107D, Media type: DVD-R
Disc Manufacturer: RITEKG - 04
Disc Application Code: 64, Disc Physical Code: 193

11:38:26 #39 Text 0 File DlgWaitCD.cpp, Line 448
>>> Protocol of DlgWaitCD activities: <<<
=========================================
Insert empty disc to write to.
(Medium in drive: Unknown. Medium required by compilation: DVD+R/RW, DVD-R/RW.)

11:38:26 #40 Text 0 File ThreadedTransferInterface.cpp, Line 1051
Prepare recorder [PIONEER DVD-RW DVR-107D] for write in CUE-sheet-DAO
DAO infos:
==========
MCN: ""
TOCType: 0x00; Session Closed, disc fixated
Tracks 1 to 1:
1: TRM_DATA_MODE1, 2048/0x00, FilePos 0 0 4524212224, ISRC ""
DAO layout:
===========
__Start_|____Track_|_Idx_|_CtrlAdr_|_RecDep_______ ___
0 | lead-in | 0 | 0x41 | 0x00
0 | 1 | 0 | 0x41 | 0x00
0 | 1 | 1 | 0x41 | 0x00
2209088 | lead-out | 1 | 0x41 | 0x00

11:38:26 #41 Phase 36 File dlgbrnst.cpp, Line 1832
Burn process started at 4x (5,540 KB/s)

11:38:27 #42 Text 0 File ThreadedTransferInterface.cpp, Line 2661
Verifying disc position of item 0 (relocatable, disc pos, no patch infos, orig at #0): write at #0

11:38:27 #43 Text 0 File DVDR.cpp, Line 2571
Recording mode: Sequential Recording Mode

11:38:27 #44 Text 0 File Mmc.cpp, Line 21774
Set BUFE: Buffer underrun protection -> ON

11:38:27 #45 Text 0 File DVDR.cpp, Line 2726
Start write address at LBA 0
DVD high compatibility mode: Yes

11:38:27 #46 Text 0 File Cdrdrv.cpp, Line 8892
---- DVD Structure: Physical Format Information (00h) ----
Layer: 0, Address: 0 (0 h), AGID: 0; Length: 2050
Book Type: DVD-R (2), Part Version: 2.0x (5), Extended Part Version: 0.0 (0)
Disc Size: 120 mm, Maximum Rate: <NOT specified>(F h)
Number of Layers: 1, Track Path: Parallel Track Path (PTP), Layer Type: recordable
Linear Density: 0,267 um/bit, Track Density: 0,74 um/track
Starting Physical Sector Number of Data Area: 30000 h (DVD-ROM, DVD-R/-RW, DVD+R/+RW)
End Physical Sector Number of Data Area: 0 h
End Sector Number in Layer 0: 0 h (LBN: FFFD0000 h, 4193920 MB)
Data in Burst Cutting Area (BCA) does not exist
Start sector number of the current Border-Out: 0 h
Start sector number of the next Border-In: 0 h
Media Specific [16..63]:
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................
00 00 00 00 00 00 00 00 - 00 00 00 00 00 00 00 00 ................

11:38:27 #47 Text 0 File Cdrdrv.cpp, Line 1288
11:38:27.437 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:40:08 #48 Text 0 File Cdrdrv.cpp, Line 1288
11:40:08.671 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:42:15 #49 Text 0 File Cdrdrv.cpp, Line 1288
11:42:15.843 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:44:48 #50 Text 0 File Cdrdrv.cpp, Line 1288
11:44:48.093 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:46:19 #51 Text 0 File Cdrdrv.cpp, Line 1288
11:46:19.203 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:47:14 #52 Text 0 File Cdrdrv.cpp, Line 1288
11:47:14.593 - PIONEER DVD-RW DVR-107D\H3 T0 : Queue again later

11:48:29 #53 TRANSFER -25 File Reader.cpp, Line 382
Error reading data

11:48:29 #54 Text 0 File Reader.cpp, Line 385
Exception value: -1

11:48:29 #55 Text 0 File ThreadedTransfer.cpp, Line 228
all writers idle, stopping conversion

11:48:29 #56 Text 0 File DVDR.cpp, Line 2969
EndDAO: Last written address was 1519487

11:48:33 #57 Phase 38 File dlgbrnst.cpp, Line 1832
Burn process failed at 4x (5,540 KB/s)

Existing drivers:
File 'Drivers\PXHELP20.SYS': Ver=2.03.18a, size=20576 bytes, created 11/06/2005 19:09:38 (Prassi/Veritas driver for win 2K)
File 'Drivers\atapi.sys': Ver=5.1.2600.2180 (xpsp_sp2_rtm.040803-2158), size=95360 bytes, created 03/08/2004 22:59:44 (Adapter driver for rec)

Registry Keys:
HKLM\Software\Microsoft\Windows NT\CurrentVersion\WinLogon\AllocateCDROMs : 0 (Security Option)

Any help anyone can give me to solve this would be greatly appreciated.

Nick

**Chewy** · 5 Jan 2006, 11:52 PM

Installed the latest drivers for my Asus motherboard's Intel chipset

for the ide and atapi optical drives, a problem.

File 'Drivers\PXHELP20.SYS': Ver=2.03.18a, size=20576 bytes, created 11/06/2005 19:09:38 (Prassi/Veritas driver for win 2K)

another accident waiting to happen

DiskPeripheral : WDC WD2000JB-00DUA0 atapi Port 0 ID 0 DMA: On
DiskPeripheral : WDC WD360GD-00FLA0 atapi Port 1 ID 0 DMA: On
DiskPeripheral : WDC WD2500JD-00GBB0 atapi Port 2 ID 0 DMA: On
CdRomPeripheral : PIONEER DVD-RW DVR-107D atapi Port 3 ID 0 DMA: On

are these 4 drives all on seperate cables as standalone masters?

all problems must be addressed, not just 1 or 2

bottom line tho:
the drive is getting up in it's years, may be dying

**Nick Hope** · 6 Jan 2006, 03:09 PM

Thanks very much for the reply Chewy. I really appreciate it and I'm ordering a BenQ DW1640 today. But regarding these configuration problems...

Originally Posted by Chewy

for the ide and atapi optical drives, a problem.

Why is that a problem? I thought I was doing the right thing as advised by the Nero website
( http://ww2.nero.com/nero6/en/FAQs_Er...ssages.html#12 ).
I ran the latest Intel Chipset software installation utility (INFINST_AUTOL.EXE) from
http://downloadfinder.intel.com/scri...4&submit=Go%21.
Should I not have done that? Can I reverse it without a full Windows reinstall?

another accident waiting to happen

I'm not sure what that Prassi/Vdriver is doing there. If it's a problem, how would I delete it?

are these 4 drives all on seperate cables as standalone masters?

Actually they are just on 2 cables. So I guess I should change the jumpers so that my C: drive is master on channel 1, DVD writer is master on channel 2, and my 2 data drives are slaves (one on each channel). Is that ideal?

Thanks again,

Nick

**Chewy** · 6 Jan 2006, 03:27 PM

Your log shows four drives on seperate ports all jumpered as master,
I would think it has something to do with those latest intel chipset drivers.

if you go into device manager you might be able to roll back the driver to
a default microsoft one for the secondary and primary ide,

Old IDE controller drivers - This is the most common cause of this error message. You must have the latest drivers for your IDE controller card to prevent it. (It�s the same for SCSI cards). Go to the website of the manufacturer of your controller card and obtain the latest drivers. Such as Intel, VIA, SIS, etc.

I wouldn't call windows xp sp2 old quite yet.

**Chewy** · 6 Jan 2006, 03:27 PM

what's the motherboard exactly?

**Nick Hope** · 6 Jan 2006, 03:48 PM

Originally Posted by Chewy

Your log shows four drives on seperate ports all jumpered as master,
I would think it has something to do with those latest intel chipset drivers.

if you go into device manager you might be able to roll back the driver to
a default microsoft one for the secondary and primary ide

Thanks again Chewy.

The drivers for the secondary and primary ide are still showing as "Microsoft 5.1.2600.2180" from 01/07/2001 so I guess we can rule that out as a problem.

The other entry under "IDE ATA/ATAPI controllers" is "Intel(R) 82801EB Ultra ATA storage controllers" and the driver for this is showing as "Intel 6.0.3.1005" from 17/11/2004. Should I try rolling that one back or is that not relevant?

Nick

**Chewy** · 6 Jan 2006, 04:09 PM

Uninstall the intel application accelerator

**Nick Hope** · 6 Jan 2006, 04:42 PM

The motherboard is an Asus P4C800E deluxe. I do not have RAID set up.

Originally Posted by Chewy

Uninstall the intel application accelerator

Intel Application Accelerator is not installed and never has been.

Nick

**Chewy** · 6 Jan 2006, 10:49 PM

I built one of those when they first came out, took 4 months and 3 bios flashes and a couple of reloads to get it just right, some goober keep leaving an external hard drive turned on and connected when they rebooted,
durn computer would stop boot and ask for default bios settings,
which with our raid stripe wouldn't boot windows.
Try rolling back the

"Intel(R) 82801EB Ultra ATA storage controllers"

I burned a lot of dvd's with a plex on that computer, that 3.2ghz cpu was
very fast with shrink.

edit: goober not allowed on any state of the art computers anymore
goober is in his fourth year of computer science at local technical school

**Chewy** · 6 Jan 2006, 11:09 PM

I ran the latest Intel Chipset software installation utility (INFINST_AUTOL.EXE) from
http://downloadfinder.intel.com/scri...4&submit=Go%21.
Should I not have done that? Can I reverse it without a full Windows reinstall?

was this related to the timing of your present burning problems?

I went back to asus

http://support.asus.com/download/download.aspx?SLanguage=en-us

didn't see any southbridge drivers but they are still putting out bios's
for that rocket board.

**Nick Hope** · 7 Jan 2006, 02:33 AM

Originally Posted by Chewy

was this related to the timing of your present burning problems?

Thanks Chewy, it is one of the steps I've tried to fix my burning problems because it was advised by the Nero support page. The burning problems arised before that. I detect no noticeable change in my computer since doing it.

I'll try rolling back that driver as you advise.

I'm also going to check my cable configuration and jumper settings in case those are causing Nero to think my devices are all masters on 4 different channels.

I'm also going to try putting the source data on another hard drive, and also putting the 107D in my external firewire box and burning from my laptop.

The changes to the Asus BIOS since my 1021 version look irrelevant to me so I doubt it's worth me flashing that.

Nick

**Chewy** · 7 Jan 2006, 02:39 AM

good luck in your investigation, you seem to have a good handle on it,
that's one of the reasons I like to have extra hardware to troubleshoot with/
another dvd burner.

be sure and let us know what in the heck was wrong

Nero 6.6 Error reading data

Nero 6.6 Error reading data

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment

Comment